Please click
items of interest to access the information:
T U R B I N E S , I N C .
PO Box 933
Highway 283 North
Altus, Oklahoma, 73522 USA
Phone: 1-800-809-1387
Fax:
1-580-477-3071
e-mail:
karen@turbinesincorporated.com
(c) 2005-2007Turbines, Inc. all rights reserved.
Webmaster: dezi@primaryflowsignal.com
LIQUID WAFER STYLE TURBINE FLOW METER
Turbines, Inc. manufactures a broad range of turbine flow meters. Because the wafer style meter relies on the process piping flanges to hold the meter in the line, it is generally less costly and consumes a shorter laying length.
For technical specifications of the Liquid Wafer Style Turbine Flow Meter please click this button:
The following table lists key information pertaining to the standard Wafer Style Turbine Flow Meter product line offered by Turbines, Inc. Special requirements are gladly handled upon request.
SERIES
WM WAFER STYLE TURBINE FLOW METER FOR LIQUID SERVICE
| Turbines Part No: | Meter Size inches | Flow Range GPM | Flow Range LPM | Flow Range MPD | Flow Range BPD | Max
Pressure PSI |
|---|---|---|---|---|---|---|
| WM0038 | 3/8" x 1" | 0.3 - 3.0 | 1.14 - 11.36 | 1.6 - 16 | 10 - 100 | 3,700 |
| WM0050 | 1/2" x 1" | 0.75 - 7.50 | 2.84 - 28.39 | 4 - 40 | 25 - 250 | 3,700 |
| WM0075 | 3/4" x 1" | 2.0- 15.0 | 7.57 - 56.78 | 11 - 80 | 68 - 514 | 3,700 |
| WM0078 | 7/8" x 1" | 3.0 - 30.0 | 11.36 - 113.56 | 16 - 160 | 100 - 1,000 | 3,700 |
| WM0100 | 1" x 1" | 5.0 - 50.0 | 18.93 - 189.27 | 27 - 270 | 170 - 1,700 | 3,700 |
| WM0100 X 2 | 1" x 2" | 5.0 - 50.0 | 18.93 - 189.27 | 27 - 270 | 170 - 1,700 | 3,700 |
| WM0150 X 2 | 1-1/2" x 2" | 15.0 - 180.0 | 56.78 - 681.35 | 80 - 1,100 | 515 - 6,000 | 3,700 |
| WM0200 X 2 | 2" x 2" | 40 - 400 | 151.41 - 1,514.12 | 210 - 2,100 | 1,300 - 13,000 | 3,700 |
| WM0300 X 3 | 3" x 3" | 60 - 600 | 227.12 - 2,271.18 | 320 - 3,200 | 2,100 - 21,000 | 3,700 |
| WM0400 X 4 | 4" x4" | 120 - 1,200 | 454.24 - 4542-36 | 654.12 - 6,541.18 | 4,100 - 41,000 | 3,700 |
Series WM Turbines Inc. Wafer Style turbine flow meters for liquid service are installed between the flanges of the existing process piping. Therefore, the working pressure capacity of meters depend upon the connecting flange design limits, except that the maximum pressure limits of the turbine meter body itself conforms to the "max pressure psi" column in the table above.
For convenience, typical working pressure standards are provided below:
SERIES WM WORKING PRESSURE TABULATION
| ANSI Flange Rating | Code/Standard | Carbon Steel | Stainless Steel |
| Class 150 | ANSI | 285 psi | 230 psi |
| Class 300 | ANSI | 740 ps | 600 psi |
| Class 600 | ANSI | 1,480 psi | 1,200 psi |
| Class 900 | ANSI | 2,220 psi | 1,800 psi |
| Class 1500 | ANSI | 3,705 psi | 3,000 psi |
PLEASE NOTE:
- The equipment referenced in the above tabulation is always in stock and ready for immediate shipment.
- All Turbines, Inc. turbine flow meters have corresponding retrofit kits available from inventory, as required. Please see Retrofit Kits for Liquid Wafer Style turbine meters.
- All specifications are accurate at the time of publication but may change at any time without prior notice. Please confirm performance specifications at the time of order to verify application requirements.
- All Turbines, Inc. turbine flow meters are subjected to a three point factory calibration to establish specific k-factor of the meter.
- K-factors of meters are not transferable.
(c) 2005 -2007 Turbines, Inc. - all rights
reserved.
This page was last updated:
Tuesday, December 06, 2005